Toro Evolution Series Manual do Utilizador

iEVOLUTIONTM Series ControllerUser’s Guide

6Power Supply Installation8"3/*/( AC power wiring must be installed and connected by qualied personnel only. All electrical components and inst

7Zone Expansion Module Installatione EVOLUTIONTM controller can be expanded using the optional 4-zone (EMOD-4) or 12-zone (EMOD-12) modules to add mo

8Valve, Pump Relay and Sensor Installation Figure 131 2MV PUMPSENSORSENSORCOMCOMStep 1 – Route valve wires from the valves, master valves, pump relay

9 Time and Date SetupEditing Time and DateStep 1 – Press the HELP/SETUP button.Step 2 – Use the Up or Down arrows to navigate to SET TIME/DATE.

10 Schedule Setupe EVOLUTIONTM controller only displays one schedule by default. See the "EWBODFE'VODUJPOT section to activate additional

11Zone Runtimes Setupe Zone Runtimes is where you select all the zones that will run in the schedule. By default, all zones are set to OFF. Modify th

12Manually Activate a Specific Zone(s)Step 1 – Press the WATER NOW button.Step 2 – Use the Up or Down arrows to navigate to ZONES. Press SELECT .

13 Water OffTurn Off Current OperationStep 1 – Press the WATER OFF button. WATER OFFRESUME WATERINGNEXT SCHEDULED START All currently active

14 Advanced FunctionsYou can access the EVOLUTIONTM controller’s advanced functions by pressing the ADVANCED button and then pressing SELECT button

15Schedule Startse Schedule Starts function allows you to view the three schedules with all four possible start times. Step 1 – While in the ADVANCED

ii

16Set Schedule Type8FFLEBZ4DIFEVMJOHSelecting Weekday scheduling will activate all 7 days of the week. You can disable any of the 7 days as a non-wat

17*OUFSWBM%BZ4DIFEVMJOHSelecting Interval watering allows you to specify the number of days between watering. Selecting an interval of 3 will prompt

184FU.POUIMZ"EKVTUUse the monthly adjust function to allow EVOLUTIONTM to automatically increase or decrease your watering with respect to the

19&SBTF4DIFEVMFUse the erase schedule function to reset the selected schedule. e schedule’s status will be set to DISABLED (except for schedule

20Sensorse Sensors function allows you to assign a rain sensor to each of the schedules. Schedules with a rain sensor assigned will not water when th

21Firmwaree Firmware function allows you to review the controller’s rmware version. Press SELECT to access the rmware version.FIRMWARECONTROLLER

22 Help/SetupAlertse EVOLUTIONTM controller always checks the system for proper function and it will provide feedback if it detects any system abnor

23Step 4 – Use the Up or Down arrows to modify the TIME’s Hour and Minutes or the DATE’s Month, Day and Year (Day, Month and Year for International

24PreferencesAccessing the Preferences MenuStep 1 – Press the HELP/SETUP button.Step 2 – Use the Up or Down arrows to navigate to PREFERENCES. Pre

25Set Date FormatStep 1 – While in the PREFERENCES menu, use the Up or Down arrows to navigate to DATE FORMAT. Press SELECT .Step 2 – Use the Up o

iii Table of ContentsController Introduction Timing Mechanism- - - - - - - - - - - - - - - - - - - - - - - - - - - - -

26 Specifications$BCJOFU%JNFOTJPOTt8Y)Y%YYNN1PXFS4QFDJGJDBUJPOTt/PSUI"NFSJDBInternal Transformer,

ivSchedule Details - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15 Maximum Schedule- - - - - - - - - -

1 ank you for purchasing Toro’s new EVOLUTIONTM Series Controller delivering unprecedented control and ease-of-use of your irrigation system. e

2Internal Components 14 5 67 8792 3 Figure 21 – Zones and Sensor Terminals VALVE TEST – Use this terminal to test a valve for proper function.24VAC

3Home Screen Messages HOME01:09PMWED01/08NEXT START 06:00AMALERT: PRESS HELPBCAATitle Bar HOMEe battery icon indicates that the controller’s VAC

4Setup ScreenWELCOMEINITIALIZINGPLEASE WAIT . . .SETUPLANGUAGE ENGLISHDATE FORMAT MM/DD/YYCLOCK 12 HOURTIME 12:01AMDATE 01/01/13BEGIN WEEK SUNDAYUpon

5 InstallationABCDCabinet Installation Use this page as a template to mark the screw location of the EVOLUTIONTM cabinet. ere are two mounting optio