Toro SitePro Central Control Manual de Instalação

Consulte online ou descarregue Manual de Instalação para Descodificadores Toro SitePro Central Control. Toro SitePro Central Control Installation Instructions Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 16
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 0
Introduction
The Field Interface Unit (FIU) provides the communications hardware link between the SitePro
TM
central computer, the SitePro
compatible field satellite controllers and the SitePro Central Decoder System components. The FIU is available in four configu-
rations to provide various combinations of wireline and radio communication paths. An auxiliary port is provided on all FIU
models for switch-type sensor input.
The FIU enclosure is designed for installation in a climate-controlled environment, next to or near the central computer, with a
maximum separation distance of 50' (15.2 m). Power for the FIU is provided by a 100–240 V a.c./12 V d.c. 50/60 Hz power
supply adaptable to both domestic and international plug receptacles. A lighted On/Off rocker switch located on the front of the
FIU controls power to the unit and is circuit-protected with a 1.5 amp fast-blow fuse. An array of indicator lights on the front
panel is provided for visual confirmation of system communication activity.
The following instructions cover installation of the Field Interface Unit (FIU), Surge Protection Unit (SPU), Duplex Modular Wall
Plate, optional Radio-Link components and optional SitePro Central Decoder System (CDS) components. For Network CDS
system installation, additional detailed installation information is provided with the Network CDS Decoder Interface Unit (DIU).
IMPORTANT: For your safety and equipment protection, please comply with all Caution and Warning statements
within this document. It is the responsibility of the installer to comply with all NEC and/or local electrical codes that
apply to the installation of this equipment. Please refer to page 16 for FCC and CISPR 22 information.
Note:
Some cabling and hardware components are provided for installation of the FIU, Surge Protection Unit (SPU) and
duplex modular wall plate. All other materials; i.e., wire, conduit, grounding conductors, communication cable, radio(s) and
related radio hardware must be purchased separately.
The diagrams on pages 15 depict the various FIU model system configurations. See
Figures 1 and 5 for model 2010
(Figure 1 - Satellite, Figure 5 - CDS), FIgure 2 for model 2020, Figure 3 for model 2011 and Figure 4 for model 2021.
SitePro
TM
Field Interface Unit, Models 2010, 2020, 2011 and 2021
Installation Instructions
13
16
12
14
15
CH 2
CH 3
CH 1
+12V DC
11
10
9
17
7
8
1
3
6
5
4
13
AUX
16
2
Figure 1 - Model 2010 (one wireline port)
1 - Field Interface Unit
2 - 12 V d.c. Power Jack
3 - Power Adapter
4 - Central Computer
5 - COM Port 1
6 - DB-9/DB-9 Serial Cable
7 - Channel 1 (in)
8 - COM Line 1 (out)
9 - RJ11 Modular Cable
10 - Duplex Modular Wall Plate
11 - Shielded Interface Cable
12 - Surge Protection Unit
13 - Communication Cable
14 - Satellite Controller
15 - Communication Cable - COM Path 1
(out to satellites)
16 - Auxiliary Port (optional for sensors)
17 - 1.5A Fuse
50' (15.2 m)
max.
Vista de página 0
1 2 3 4 5 6 ... 15 16

Resumo do Conteúdo

Página 1 - Installation Instructions

IntroductionThe Field Interface Unit (FIU) provides the communications hardware link between the SiteProTMcentral computer, the SiteProcompatible fiel

Página 2

Note: The Motorola radio service software screens shown inFigure 12, 13, and 14 are for example only. Later servicesoftware versions may not be format

Página 3

Radio-Link System Setup1. Reconnect power to the FIU and switch on all components. The central computer should be booted up and the SitePro pro-gram o

Página 4

SitePro Central Decoder System ConnectionThe SitePro Central Decoder System (CDS) program works in conjunction with the SitePro Field Interface Unit M

Página 5

45665427Pin 2Pin 2Pin 1Pin 12331Figure 16 - DIU Connection OverviewFigure 17RJ45 Cable to Wall Plate13YellowYellowYellowGrayGrayGray1 - Surge Protecti

Página 6 - Earth Ground Installation

14Figure 18 - Illustrated Parts Listing, FIU Models 2010, 2020, 2011 and 2021See Detail BSee Detail CDetail BDetail CPhone JackView A-A(Bottom View of

Página 7

15Item No. Part No. Description QuantityPer Assy.Refer to Figure 18 for the following items:1 - - - - - - - Housing, SNCX, FIU 12 - - - - - - - Brac

Página 8 - FIU Front Panel Components

TroubleshootingIf a malfunction occurs, follow the suggested steps to identify and fix the problem. If the problem cannot be resolved theremay be a pr

Página 9 - Satellite System Setup

6557158910111316141718201219222123241234Figure 2 - Model 2020 (two wireline ports)1 - Central Computer2 - Field Interface Unit 3 - COM Port 14 - COM P

Página 10

3671389101114151618171912122035542124232526 221 - Central Computer 2 - Field Interface Unit 3 - COM Port 1 4 - COM Port 25 - DB-9/DB-9 Serial C

Página 11

781917910121113202122242325272628126661814163451531303233291 - Central Computer2 - Field Interface Unit3 - COM Port 14 - COM Port 25 - COM Port 36 - D

Página 12

Installing the Field Interface Unit, Wall Plate Assembly and Surge Protection Unit 1. Position the Field Interface Unit within 6' (1.8 m) of the

Página 13

7. A 25' (7.6 m) length interface cable is supplied for the connection of the modular wall plate to the SPU. Select an installa-tion site for the

Página 14

Procedure1. Drive a 5/8" (16 mm) by 8' (2.5 cm) copper-clad steelground rod into well-moistened soil not more than 8' (2.5 cm) from the

Página 15 - FIU Internal Modem Breakdown

Communication Cable TestCorrect installation of the communication cable is essential for proper operation of the wireline control system. The communi-

Página 16

Processor Ready: Indicator light will illuminate when the microprocessor in the FIU has received configuration instructionsfrom PC and is ready to com

Comentários a estes Manuais

Sem comentários